MEE6501 Waldorf University Air Quality and PBR Evaluation Research Paper

Question Description

Need 2 full pages double-spaced (not including title and references pages)

Be careful to instructions and dont plagiarize

develop a document titled “A Permit by Rule (PBR) Evaluation for a Painting Operation” and will serve as a simulation of our work as a contract environmental engineer to an industrial organization planning a painting operation within the United States.

The Scenario:

You have contracted with an industrial organization to engineer and write a state air Permit by Rule (PBR) evaluation for a painting operation facility. According to the local state laws and U.S. Environmental Protection Agency (EPA) laws, the facility must have an air permit before construction begins. Once the facility is completed, the construction air permit will then become the operational air permit for the facility.

As a result, your client wants the air permit to automatically align the painting operation facility into operational compliance with state and federal air quality laws. Consequently, it is extremely important for you to evaluate the planned painting operation against the PBR requirements in order to meet the air permit criteria, using the state guidance document and considering the equipment and chemicals already planned for the facility operations.

You have tabulated the following information from what you have gleaned from the material SDS documents and equipment technical data sheets plan (depending on your scenario selection, each “unit” represents a single aircraft, rail tank car, or vehicle):

Interior Liner Coating Material 10 gallons coating/unit 2 gallons of solvent/unit
Unit Lining Application Apply interior liners to two (2) units/day Work five (5) hours/day and four (4) days/week
Unit Lining Curing Cure interior liners of two (2) units/day Work five (5) hours/day and four (4) days/week
Interior Liner Cure Heater fuel source is natural gas-fired drying oven Heater generates 2.1 million (MM) Btu/hr at maximum 2,500 hrs/year
Unit Lining Design Cross-draft air plenum Unit interior is the spray area
Exhaust Fan 10,000 ft3/min (CFM) 1 exhaust fan
Air Makeup Unit 5760 ft3/min (CFM) 1 air makeup system
Filter Openings 20.0 ft2 each Two (2) filter openings
Coating WV VOC content 2.8 lb/gal coating
Coating VM Coating volume 1.0 gal
Water Content Per gal/coating 1.0 lb/gal
Water Density Per gal/water 8.34 lb/gal
Coating VW Water volume Calculation
Exempt-solvent Content Per gal/coating 0.5 lb/gal
Exempt-solvent Density Per gal/exempt solvent 6.64 lb/gal
Coating Ves Exempt solvent volume Calculation

Additionally, your state’s department of environmental quality (DEQ) has provided you the following PBR limits:

Potential to Emit (PTE) 100 tons VOC/year
Face Velocity 100 ft/min
Filter Velocity 250 ft/min
VOC/5-hour period 6.0 lbs/hr
Short-term Emissions 1.0 lbs/hr
Long-term Emissions 1.0 tons/yr

From your first visit with your client, these are your notes and process flow sketch reflecting the intended operational design:

  • The client has designed an interior coating spray painting system that allows the interior of each unit to be coated.
  • The operations will involve a stripped-down unit being brought into the facility’s shop.
  • The shop is a steel building with a finished concrete floor and a paint booth for each unit.
  • The unit will be placed in the spray booth.
  • The booth will be opened at one end of the booth for makeup air.
  • The exhaust air will flow through an exhaust chamber at the other end of the unit.
  • For each unit, once the liner application operations are completed, the forced curing (drying) operations will immediately commence.

Instructions:

  1. Closely read the required reading assignment from the textbook and the unit lesson within the study guide, and consider reading the suggested reading.
  2. Select the PBR evaluation document to be for only one of the following: (a) an aircraft manufacturing exterior coating paint booth, (b) a rail tank car interior lining process, or (c) a vehicle exterior coating paint booth. You will continue with this scenario selection for the remaining six units, to complete the entire document.
  3. Using APA style (title page, abstract page, body with level 1 headings, and a reference page) for a research paper, begin drafting a PBR evaluation document. You will add to this document in every subsequent unit with another prescribed level 1 heading, building out the entire document one section at a time.
  4. Make your Unit II work the first level 1 heading (center, bold) titled “General Considerations for Operation,” and describe the scenario that is presented above, while specifically describing the scenario that you selected (aircraft, tank car, or vehicle). While describing your scenario, you must include the environmental, health, and safety (EHS) implications of the work system while pulling from the textbook as well as any other relevant sources that are presented in the unit lesson in the study guide. In your description of the EHS implications of the system, be sure to discuss the natural and anthropomorphic variables causally related to outdoor air pollution. You are required to describe the scenario in at least 200 words (minimum). You may find it convenient to summarize the tabulated information in your General Considerations section of the permit for future reference throughout the rest of the course, but do not attempt to tabulate the information in the exact order as what is presented here (to avoid a high match in SafeAssign).
  5. Also under the first level 1 heading, present a box and line process flow diagram (PFD) drawing of the selected scenario. See the drawing on page 375 of the textbook as an additional example of a PFD if you need assistance understanding how to draw one; do not draw the same system that is provided on that page. Do not hand-draw this, but use the “insert” and “shapes” features within Microsoft Word to construct the PFD. Simple labeled boxes and lines are adequate for this preliminary work, so it is not necessary to present specific shapes in your PFD for your selected scenario.
  6. In your abstract section (page 2 of the document), write one or two sentences that reflect your work for this unit. We will be adding one sentence per unit to reflect our work as we go, with the final abstract length being about 8 to 10 sentences long.

In following units (Units III through VII), the unit lessons will contain information related to the interior surface coating operation by means of practical mathematical calculation examples. Consequently, it is imperative that you read the unit lessons within the study guide in every unit, use the math calculation examples provided in each unit lesson, and consider the current (as well as previous) material from the textbook and the additional information cited and referenced in the study guide for every unit. This project will serve as a comprehensive demonstration of your applied learning of engineering air quality.

Your completed mini project should be a minimum of one page, not counting the title page, abstract page, and reference page. You are required to use at least one outside source, which may be your textbook. All sources used, including the textbook, must be referenced; paraphrased and quoted material must have accompanying APA citations.

Unformatted Attachment Preview

Instructions Our course project will be to develop a document titled “A Permit by Rule (PBR) Evaluation for a Painting Operation” and will serve as a simulation of our work as a contract environmental engineer to an industrial organization planning a painting operation within the United States. The Scenario: You have contracted with an industrial organization to engineer and write a state air Permit by Rule (PBR) evaluation for a painting operation facility. According to the local state laws and U.S. Environmental Protection Agency (EPA) laws, the facility must have an air permit before construction begins. Once the facility is completed, the construction air permit will then become the operational air permit for the facility. As a result, your client wants the air permit to automatically align the painting operation facility into operational compliance with state and federal air quality laws. Consequently, it is extremely important for you to evaluate the planned painting operation against the PBR requirements in order to meet the air permit criteria, using the state guidance document and considering the equipment and chemicals already planned for the facility operations. You have tabulated the following information from what you have gleaned from the material SDS documents and equipment technical data sheets plan (depending on your scenario selection, each “unit” represents a single aircraft, rail tank car, or vehicle): Interior Liner Coating 10 gallons coating/unit Material 2 gallons of solvent/unit Unit Lining Application Apply interior liners to two (2) units/day Work five (5) hours/day and four (4) days/week Unit Lining Curing Cure interior liners of two (2) units/day Work five (5) hours/day and four (4) days/week Interior Liner Cure Heater fuel source is natural gas- Heater generates 2.1 million (MM) Btu/hr at fired drying oven maximum 2,500 hrs/year Unit Lining Design Cross-draft air plenum Unit interior is the spray area Exhaust Fan 10,000 ft3/min (CFM) 1 exhaust fan Air Makeup Unit 5760 ft3/min (CFM) 1 air makeup system Filter Openings 20.0 ft2 each Two (2) filter openings Coating WV VOC content 2.8 lb/gal coating Coating VM Coating volume 1.0 gal Water Content Per gal/coating 1.0 lb/gal Water Density Per gal/water 8.34 lb/gal Coating VW Water volume Calculation Exempt-solvent Content Per gal/coating 0.5 lb/gal Exempt-solvent Density Per gal/exempt solvent 6.64 lb/gal Coating Ves Exempt solvent volume Calculation Additionally, your state’s department of environmental quality (DEQ) has provided you the following PBR limits: Potential to Emit (PTE) 100 tons VOC/year Face Velocity 100 ft/min Filter Velocity 250 ft/min VOC/5-hour period 6.0 lbs/hr Short-term Emissions 1.0 lbs/hr Long-term Emissions 1.0 tons/yr From your first visit with your client, these are your notes and process flow sketch reflecting the intended operational design: ▪ The client has designed an interior coating spray painting system that allows the interior of each unit to be coated. ▪ The operations will involve a stripped-down unit being brought into the facility’s shop. ▪ The shop is a steel building with a finished concrete floor and a paint booth for each unit. ▪ The unit will be placed in the spray booth. ▪ The booth will be opened at one end of the booth for makeup air. ▪ The exhaust air will flow through an exhaust chamber at the other end of the unit. ▪ For each unit, once the liner application operations are completed, the forced curing (drying) operations will immediately commence. Instructions: 1. Closely read the required reading assignment from the textbook and the unit lesson within the study guide, and consider reading the suggested reading. 2. Select the PBR evaluation document to be for only one of the following: (a) an aircraft manufacturing exterior coating paint booth, (b) a rail tank car interior lining process, or (c) a vehicle exterior coating paint booth. You will continue with this scenario selection for the remaining six units, to complete the entire document. 3. Using APA style (title page, abstract page, body with level 1 headings, and a reference page) for a research paper, begin drafting a PBR evaluation document. You will add to this document in every subsequent unit with another prescribed level 1 heading, building out the entire document one section at a time. 4. Make your Unit II work the first level 1 heading (center, bold) titled “General Considerations for Operation,” and describe the scenario that is presented above, while specifically describing the scenario that you selected (aircraft, tank car, or vehicle). While describing your scenario, you must include the environmental, health, and safety (EHS) implications of the work system while pulling from the textbook as well as any other relevant sources that are presented in the unit lesson in the study guide. In your description of the EHS implications of the system, be sure to discuss the natural and anthropomorphic variables causally related to outdoor air pollution. You are required to describe the scenario in at least 200 words (minimum). You may find it convenient to summarize the tabulated information in your General Considerations section of the permit for future reference throughout the rest of the course, but do not attempt to tabulate the information in the exact order as what is presented here (to avoid a high match in SafeAssign). 5. Also under the first level 1 heading, present a box and line process flow diagram (PFD) drawing of the selected scenario. See the drawing on page 375 of the textbook as an additional example of a PFD if you need assistance understanding how to draw one; do not draw the same system that is provided on that page. Do not hand-draw this, but use the “insert” and “shapes” features within Microsoft Word to construct the PFD. Simple labeled boxes and lines are adequate for this preliminary work, so it is not necessary to present specific shapes in your PFD for your selected scenario. 6. In your abstract section (page 2 of the document), write one or two sentences that reflect your work for this unit. We will be adding one sentence per unit to reflect our work as we go, with the final abstract length being about 8 to 10 sentences long. In following units (Units III through VII), the unit lessons will contain information related to the interior surface coating operation by means of practical mathematical calculation examples. Consequently, it is imperative that you read the unit lessons within the study guide in every unit, use the math calculation examples provided in each unit lesson, and consider the current (as well as previous) material from the textbook and the additional information cited and referenced in the study guide for every unit. This project will serve as a comprehensive demonstration of your applied learning of engineering air quality. Your completed mini project should be a minimum of one page, not counting the title page, abstract page, and reference page. You are required to use at least one outside source, which may be your textbook. All sources used, including the textbook, must be referenced; paraphrased and quoted material must have accompanying APA citations. …
Purchase answer to see full attachment

Place this order or similar order and get an amazing discount. USE Discount “GET12” for 12%